Monday, 30 March 2015

Trans Equatorial Propagation

Trans equatorial propagation, something I don't get here.

This image is from DXMAPS, and I shall add a link to the DX Maps site. It is a brilliant site. I contribute to it, anyone can watch it. It is run by Gabriel, EA6VQ. It must be a lot of work, and I think it is worth contributing some Euros from time to time in exchange for this great service. Not only can you see the spots on a map, you can also see the list of contacts. Very useful is the "ES MUF" map, which shows were the Es clouds must be located. Very helpful.

The shot above shows TEP in full swing on 6m, though it also works in my beloved 28MHz and 70MHz bands too. TEP does not come as far North as 56 degrees. These contacts are often 7000km+ - e.g. Greece to South Africa or Reunion in the Indian Ocean - quite something for VHF. All I can do is sit and watch it all happen.

There are several reasons why TEP does not work from this QTH. One is that the geometry of the situation does not extend this far North. The "equator" in this case is the magnetic equator, which is displaced from the geographical equator. Even then, I am probably too far from the equator to see the ionised clouds on either side of it. Secondly, a comparable distance South from here would be South of Africa, in the Southern Ocean. Not much activity there.

If you look at the Americas, where there is territory further South, the picture is different anyway as the magnetic equator is differently sited there - yes they do make TEP contacts from Argentina, but not as far North as we get in Europe. The magnetic equator is North of the geographic equator on the Europe/Africa axis, but further South on the American axis. So it is a mixed bag.

Recently though I saw a TEP spot on DX Maps from a station about 250km South of me. That is a lot closer than usual. He was only hearing a beacon, which I bet was frustrating for him. We do not know if it was possible 2-way and if a QSO could have resulted. However it shows that, given the right conditions, TEP can come relatively close to me.

Maybe one day there will be a TEP opening from here. Given the right conditions, other propagatiion modes could link into TEP. For instance, perhaps Sporadic E could carry my signal far enough South to reach the Northern extent of TEP. The snag is that Es occur here in the Summer (and for a few days in Winter) whereas TEP generally occurs in Spring and Autumn. So there might only be a few days each year with the potential for it to work (if it would work at all).

Other methods of bringing my signal South have been suggested as a way to link into TEP. Tropo ducting might work but since I moved here there has only been one good tropo opening in 7 years, and a couple of limited ducts. Still, it might work. Certainly in the late 1970s there were quite a few tropo openings but that seems to be a thing of the past now (climate change?). Tropo scatter might also work, but it would be VERY weak. Right now I do not have a very good 6m antenna.

And then the other factor arises. How badly do I want to gain access to TEP? You might say "move to France or Portugal". Yeah, well then I would lose most of my beloved aurora, auroral Es, Thule-Es and so forth. Auroras are less predictable than TEP, but maybe that makes them more fun. Ordinary sporadic Es are much less common here than in the South, but I value them more. Maybe their very rareness makes me appreciate them. Anyway, how could I deal with all the sun and the lack of snow, gales, and driving rain? How could I get Fig Rolls and Newcastle Brown Ale in Portugal?


So maybe I just have to accept it, I need to watch TEP going on and accept that it is not for me.

But you never know.

I seem to do OK without it.

73s

Jim
GM4FVM
Thanks to Gabriel for permission to use the screen shot.

Sunday, 29 March 2015

6metres and how I can't climb any more

OK, the 6m antenna is now up and ready to go.
Unlike my 4m or 2m horizontal antennas, this is a not a DX one. Perfectly effective, the Diamond A502HB is not exactly a high performer. It claims 6.3dBi gain, which is good for a 2 element, but not in the 3 element class. Having replaced a 3 ele on 6m with a claimed gain of 7.24 dBi, it could be seen as a step backwards.

The explanation for this is that the previous antenna was a dual band 4m/6m, and that space is now occupied by a much better 4m antenna, so 6m will have to get along with this. So the 2m half wave which was up on this bracket has been replaced by a vertical dipole on the main mast, and this rather weak bracket now has to support the 6m set-up. Why not put the 2m half wave vertical on the main mast - well I tried, but it only takes a 37.5mm mast and my main mast is 50mm.

This is starting to sound more like an edition of Peyton Place than a radio blog (reference only understood by those over 95 years old). Erm .. struggling for a more modern comparision ... more like a Twin Peaks edition. Now that shows my age too.

The Diamond antenna is often referred to as a Yagi, including by Diamond America. But in fact it appears to be based on the HB9CV design (not that Diamond say THAT). Both elements are driven and the arrangment is entirely out of the HB9CV design book. That is what gives it extra performance over a Yagi and in particular a very short boom. It only loses about 1dB over my old 3 element Yagi, and I have worked Puerto Rico on that. So it is perfect for lightweight rotators and simple brackets.

Key to the whole thing is that all the materials, except the 3 core mains flex used for rotator control, was already on the premises and therefore cost nothing extra.

OK, the 6m set up is RG-213 co-ax, two old 6 inch TV mast brackets, Conrad £50 rotator, Diamond AH502HB and two 1.25m lengths of 37.5mm OD thick wall ali mast. The design issues here are obvious. "It'll fall down", you say. These brackets held a Watson X-30 "co-linear" (actually a half wave on 2m and only a co-linear on 70cms). Now they have a much heavier load. The rotator is lightweight in rotator terms but heavy for the brackets. I have split the pole lengths roughly evenly. I had intended to have a shorter 50mm pole at the bottom - but the brackets only take 37.5mm !!!! Also, the rotator is only meant for light duty, and seeing it with a two metre long pole above it scared me. So compromise is the order of the day.

I first put it up two days ago and tested it about 50cms lower in a wind of 80kph gusts. It whipped about a bit, but lasted the wind. We do get well over 100kph gusts here. Now it is at full height. Worries are whether the rotator can take it and whether the brackets can take it.

Now here is the awkward bit. The obvious thing to have done was to leave my 2m vertical where it was and put the Diamond under the Sirio 4m vertical I have. It is supported by good strong T and K brackets, well bolted into the wall. And why not? Because I have lost the ability to climb up and work at the height of the Sirio. It was me who put that antenna up there, but that was years ago and now I cannot reach it. Here is a photo of my scaffolding tower which I previously used to reach the Sirio brackets...
The scaffolding tower is a neat thing. In this picture the working platform is about two rungs (about a metre) lower than needed to reach the top bracket. But this week I could not work with the platform any higher. So basically I cannot work on this antenna any longer. I am toying with the idea of getting someone to move the top bracket down below the bottom one, and maybe then I could manage.

I do not know how I lost my head for heights. As it stands, the Diamond 6m beam is now about 50cm below the ridge tiles of the roof. That might do for meteor scatter or Sporadic E, but it rules out much tropo. It really ought to be up in the clear on the same mast as the Sirio, but just for now I cannot organise it.

In a bid to prove that it all worked, I used the Diamond to put out some calls on 6m meteor scatter. I worked 2E1IIP and GM6NX - both on tropo! (To be fair, they were not working anyone on meteor scatter either, so propagation was not great). We shall see how effective this proves to be. Either I need to get over my sudden loss of ability to work at heights, or I need to get someone in to change things. And then again maybe the wind will blow it all down anyway.

Or a second tilt-over mast?

73.

Jim


Tuesday, 24 March 2015

Meet the handhelds

I am a tutor and examiner for the UK amateur licence exams, but the local clubs cannot be bothered to allow me to run courses. But for a while I did and one candidate arrived here to do his morse familiarisation (me teaching someone morse is an interesting idea). He looked around the shack in amazement and said "why do you need five radios?".

Good point. That stumped me. There is an explanation of a sort, and more of that later. What he did not know was that I have four more in the shape of handhelds.

Before I had the current four I had Yaesu VX5 and 6s, (two band 144/430 MHz, and one had 50MHz as well, not that 50MHz was very useful) and a Wouxun KG-699E 70MHz one. Years ago I started with a Trio (Kenwood) TR2200 - 1 watt, weak, deaf and with hopeless Ni-Cad batteries. The TR-2200 was less of a hand portable and more of a "luggable": bigger and heavier than a Yaesu FT-817 but with just six (expensive) 144MHz crystal controlled frequencies. I also had a hand portable in the 1970s, the name of which escapes me. I think it was called a "Ken" or something. It was equally useless. It was not until the 1990s and the Yaesu VX range with lithium batteries that they became practical for me.

Lined up here like something out of a police drama, are the four suspects:-



They are, from left to right, a Baofeng BF-888F, a Baofeng UV-5R+ Plus, and two (yes, two!)  Wouxun KG-UV6Ds. The Wouxun on the extreme right is in its desk charger.

The Baofengs are really a pair. Baofeng, now renamed Pofung (surprising move that), make radios that are ... value for money. In this case, £10 and £30. You might not expect much for that money, and not much is what you get. They are OK. In many ways I respect them more than the Yaesu VX5 and VX6 that went before them. The VX6 is now £200, and I cannot see what use increasing the price by a factor of 7 over the UV5-R+ brought me.

The 888 is a basic thing. It has no display and so you have to program it using a cable. There are 16 channels available to program in its 400-470 MHz range. It runs about 2 watts max (a little less maybe). It comes with a lousy antenna - but all these things do. First step in cheap handpoartable land - replace the antenna with a Nagoya one. All parts like the antenna, mics, power leads, spare batteries for cheap handhelds are easily and cheaply available from Hong Kong via eBay. Including must-have Nagoya antennas.

I bought that 888 to work with the UV-5R+ Plus (yes, that is plus,plus according to the front panel). It can also listen on most of the licence-free European PMR frequencies. Not all because it does not have the right steps, but most. Of course, it would not be legal to transmit on those frequencies with this rig as at 2W it is vastly over-powered. Also, it has that demon of things, a replaceable antenna. The PMR spec is for 500mW and fixed antennas - and PMR rigs cost four or fives times as much for a lower spec. As Granny Edgar used to say "The World is ill-divid".

Anyway, apparently some people use cheap rigs like this to tx on the PMR frequencies, but I know NOTHING about that. I can use it legally on the 70cm amateur band, and listen on PMR. My plan was to use it on the local GB3BE repeater, only to find that although BE gives its CTCSS code for a 118.8hz tone every time it identifies itself, it does not accept the tones. It only opens for a 1750hz toneburst which the 888 does not have. So that idea is out the window, and the world is even more ill-divid than I thought. But at £10 do I care? No. Apart from that issue (which is not the 888's fault, as it never claimed to have a toneburst) it works fine and for the money I have have had no problems.

The UV-5R+ was a replacement for the Yaesu VXs. I have a 12V back to replace the battery for mobile use, which is what I did with it until the Wouxuns arrived. I find that the only speaker/mics that sound at all good are the Wouxun branded ones, and that was what I used with it. I might say that I just listen when mobile, and rarely transmit.

The UV-5R is a good rig, runs about 5W max and has a frequency range of 136-174 and 400-480MHz. It has a 1750hz toneburst as well as the usual CTCSS and stuff. Unlike the 888, it has a display screen. As it has a display you can in theory program the memories by hand, but I suspect that using a computer makes it much easier. Some of the UV-5Rs I hear sound a bit strangled, so using a speaker/mic is a good idea. It also has an FM broadcast receiver built in which can be set to mute when the squelch opens on the ham side. Note: replace the antenna!

Not much to say about the UV5-R. I used it sometimes as a replacement shack rig when the main 2m FM rig went belly-up, and the (two) replacements also failed. Provided I used the Wouxun speaker mike, it was fine. One more thing it will do which the VX5s etc would not (after the dual FM/Ham radio trick!) is that I can program it for use in North America, as the Yaesus sold in Europe were limited to 144-146. And of course it will listen to some PMR channels.

The UV5-R+ is now the rig I use in my workshop over the garage where I build model trains, DCC control and interlocking, and the like.

Now, the two Wouxuns were bought separately, but always with the idea of reducing the handheld count by one. Which never happened.

It went this way. When I went mobile I was taking the UV5-R for 2m and my single band Wouxun KG-699 for 4m. That was a pain as I had to stop the car and swop rigs to change band. So when the Wouxun KG-UV6D dual band appeared (range 66-88 and 136-175 Mhz) I bought one to use mobile. The plan was to sell the Wouxun KG-699 I had (which I did), and sell the UV-5R+ (which I didn't as it forms a pair with the 888). Then I could use the dual band KG-UV6D in the car and for general handie type purposes.

That UV6D rig, rig "A", lasted a week before I dropped it on a concrete road surface and then the next day into our garden pond. When it came out of the pond it would not work, the display was blank and there was a leaf floating in water inside the display. That was maybe looking  bad for the rig, so I phoned the importers who told me that it was beyond redemption and I bought another one (rig "B").

Later I looked up the spec and Wouxun claimed that the UV6D can survive brief immersion. As they are intended to be used as site radios, so they are built to get wet (though dropping into a pond is not really expected, and it did take a few minutes for me to wade in and retrieve it). It does not claim to be "submersible", but maybe it would recover. So I carefully stored rig "A" without the battery in a airy place, and left it very much alone to see if it would dry out. After a couple of weeks I reconnected the battery and sounds came out but the display was dead (but it had dried out). After another couple of weeks I tried again and rig A came to life and has never looked back. The leaf dried out, turned to powder, and fell out again. I doubt if that was good for it in the long term, but we are where we are.

So I have two.

Rig A lives in the car and is now my mobile rig. That is probably a good thing as the little SMA-type antenna sockets do not take well to repeated unscrewing. I use a pigtail bought on eBay so when I want to take it out of the car I disconnect the PL-259 end. You can see the pigtail in the photo. I can take it out if I am leaving the car in an exposed place (not that car crime is a big issue out here). I have a 12V battery replacement back for it so it works on the car DC supply.

Rig B is a shack rig, used for portable, general signal generation and so forth. I don't need two, but I have two, so there you go. Two batteries is a handy arrangement.

Performance-wise the Wouxuns are a step above the Baofengs. Audio quality is excellent, but then again the Wouxun rigs are about £80 for this model. The receivers are more sensitve and the harmonic radiation is vastly better. I wouldn't connect a Baofeng to a linear amplifier but I have done with the Wouxuns. The display is clearer, the rig sits more comfortably in the hand, the controls work more smoothly. Man, the Wouxun is the handportable-lovers handportable. After the KG-699 (which was excellent) I had thought that the dual band UV6Ds might be less effective, but they just work fine.

The antenna supplied with the UV6D is not quite as bad as some, certainly better than the KG-699 one was, but I would replace it if you can. The usual Nagoya does for 2m and a Garex (now Spectrum) wavy-thing does for 4m. I also have a 4m bottom loaded whip which is quite good. In the car I need a diplexer and two antennas for both bands.

OK, so these rigs are value for money. They work. The programming software can be a pain. You can find it in various places such as the "409 Shop" website (I bought my first Wouxun KG-699 from 409 Shop and bought various bits over the years and they are reliable suppliers in my experience). The software gets tricky with the UV-5R+ which has various versions and not all the software works with all the rigs. Luckily I bought a generic programming lead with a disc enclosed which is for "UV5-R New" which works with mine. Trial and eror may be required. I believe that "Chirp" works well in Linux and it will program almost all of them.

When it comes to programming leads, quite a few of them have "fake" Prolific chips in them. The driver discs in the leads will work, until Prolific update the driver via Windows update. Naturally, Prolific are not keen on having their chips ripped off, so they have every right to update their software to a version which stops the fakes working. However, in Windows 7, at least, you can assign the old driver to a specific device (select "chose a driver from a list" and juggle them about). That will work until Prolific issue another update. Works for me anyway.

So, for all these rigs, they work well as far as they should for the money. They might even survive dropping onto concrete surfaces and into ponds (but I do not recommend it). They are programmable (fiddly) , you can find accessories cheaply, there are good speaker mics (well, Wouxuns mics anyway) and they take well to good antennas. What is to complain about? Not much.

But I think that four handhelds is enough.

73

Jim

Monday, 23 March 2015

WSPR update No 1

Getting better - 20mW does it ...


Power Reported Distance
Date Call Frequency SNR Drift Grid dBm W by loc km mi
 2015-03-23 15:30  GM4FVM  28.126100  -26  0  IO85wu  +13  0.020  EA/LA3JJ  IL38ar  3159  1963 

QRP, WSPR and concrete dust.

What do I do WSPR for?

To see how far I can get on low power - testing propagation at the same time. This tests my equipment and antennas as well of course. The fact that you can see how well a distant station can receive you is what I do it for.

Also, you can fit in WSPR alongside other things you are doing. In my case today it is chippping up a concrete floor, in inch-square pieces, on my hands and knees, with a chisel and a very large hammer.

Today WSPR has been about what power I needed to work Jon Ove, EA8/LA3JJ, on Fuertaventura in the Canary Islands.

At 11:44 he could receive me at +3dB when I ran one watt. So I cut it steadily to 50mW, at which stage I had fallen to -25dB. After that it dropped out and he cannot hear me now even though I am now running 200mW. Conditions change. It is 3159km from here to Jon Ove's location.

By dropping the power in this, a coupe of  was I worked Chris 4X1RF (3833km) on 1mW. That is the equivalent of 3,833,000 km per watt.

Power Reported Distance
Date Call Frequency SNR Drift Grid dBm W by loc





































 2015-03-23 13:14  GM4FVM  28.126096  -21  0  IO85wu  +27  0.501  EA/LA3JJ  IL38ar 

 2015-03-23 12:28  GM4FVM  28.126096  -25  0  IO85wu  +17  0.050  EA/LA3JJ  IL38ar 

 2015-03-23 12:20  GM4FVM  28.126097  -15  0  IO85wu  +20  0.100  EA/LA3JJ  IL38ar 

 2015-03-23 12:08  GM4FVM  28.126099  -12  -1  IO85wu  +23  0.200  EA/LA3JJ  IL38ar 

 2015-03-23 11:52  GM4FVM  28.126099  -7  0  IO85wu  +30  1.000  EA/LA3JJ  IL38ar 

 2015-03-23 11:44  GM4FVM  28.126099  +3  -1  IO85wu  +30  1.000  EA/LA3JJ  IL38ar 

 2015-03-23 11:24  GM4FVM  28.126099  -2  0  IO85wu  +30  1.000  EA/LA3JJ  IL38ar 

 2015-03-23 10:54  GM4FVM  28.126099  -9  0  IO85wu  +30  1.000  EA/LA3JJ  IL38ar 

















I do not intend to post here so often in future but I have a backlog!




























73






















Jim













































































































































































































Sunday, 22 March 2015

10m sporadic E & when do I get VHF Es?

OK, from here to Brazil or Australia is not really Sporadic Es, but todays 10m contacts were LARGELY European Es.


It has taken 5 days for 10 metres to return to more or less normal. After the 17 March CME there were a couple of days of more or less blackout, but now we have the Europeans. Note, no stations from US or Canada, who I would normally expect around now.

So when can I expect any VHF Sporadic E?

It takes more ionisation of the E layer for Es on VHF than 10m - obviously. That means VHF Es here is a "Summer" event. Maybe nearer to the Equator it happens most of the year, but up here in chilly 56 degrees North we have to wait for either Summer or some odd event (such as the so-called "Christmas Es", which usually happen in January). (?).

Looking back in my log is not very accurate. Some years I am on holiday, sometimes I am doing something else. But here are the dates of the arrival of VHF Es here for the past few years:--
2010
24 May S51DI JN76 1618km - 70MHz FM.
2011
9 May F9IE IN86 991km - 50MHz
9 May CT1QP IM58 1969km - 70Mhz
2012
2 May IK0FTA JN61 1878km 70MHz
2013
24 April I5XX JN53 1661km - 50Mhz
1 May IS0AWZ JM49 2022km - 70MHz
2014
8 May OH6WD KP23 1760km - 50MHz
10May SP2JYB JO92 1387km - 70Mhz

Where the 6m one was first then I listed the 4m to see how much later it was (if at all). I do not think that 2010 is very representative as my transverter was away for repair and I did not have a 6m antenna up. However, FM signals do quite well on Es so it might say something, if only how badly prepared I was in 2010.

So, I might expect 6m Es in about 4 weeks (late April on), and 4m Es in about 6 weeks time (early May).

Time to get the 6m antenna up. I have been working on it, but I need to step on the gas.

73
Jim

Friday, 20 March 2015

More aurora guff.

Solarham says that the St Patrick's Day aurora was the most powerful event to hit Earth in this Solar Cycle. They may be right. They did a feature here ..  http://www.solarham.net/march2015storm/index.htm . Solarham is a great site and deserves support.

I am going to revise my total worked in the 17 March 2015 aurora. It is down from 45 to 44.

Looking at my contact with LA3EQ, it was the last of the first wave of activity at 17:50. It was the only station not to be located South of me. I was beaming throughout the event at 50 degrees, which is right at Jan. He mentioned he had turn his beam to the West. He is just 563km from me over a sea path. The audio quality was quite good though not T5. So I think that is was mixed Auroral scatter/Auroral Es contact.

That reduces my total to 44 but then again it was part of the auroral event, so I will increase it back to 45 again. 44 auroral scatter and one mixed mode.

My best DX was OZ8ABE in JO55 square at 877km,  Over 600km were PE1COS (JO33) 632km, PA3EGH (JO21) 652km, ON5VW (JO10) 657km, PA4VHF (JO32) 710km, PE1IWT (JO32) 712km, OZ1JXY (JO46) 735km, ON4PS (JO20) 738km, OZ5KM (JO45) 741km, OZ2OE (JO45) 742km, OZ1BNN (JO55) 840km, OZ3ZW (JO54) 866km.

Hats off to EI4DQ (IO51) being the only station in "these islands" to almost break 600km, at 593km. And of course ON4ADI calling on CW made my day (as I was able to read it!!!), and in JO11 Paul is just 594km from here.

Any of those contacts on its own would be a great QSO for VHF, never mind a shed load of them making quite a day.

You do not have to be far away to be appreciated. Another choice contact was G4FVP, who I have now worked on tropo and very short skip Es, and now also on aurora. In IO94, Clive was the nearest of many G stations at 151km. I cannot hear him unless there is some sort of lift in conditions. With a call like that, Clive and I must have got our Class A licences almost on the same day. Also, G8JVM must have been pretty close to me for Class B, as I was G8JWG. Did we sit the same exam in December 1974?

Finally, closest station to me, and the only GM I worked that day, was Andy, GM4JR. Andy is also in IO85, and only 121km away. However, the path is right through the Southern Uplands, so we never work easily - but on 17 March he was blasting away at 59A +++.


73
Jim
GM4FVM

Thursday, 19 March 2015

Is the IC-7100 a good rig?

I have an IC-7100. All of those 45 aurora contacts made on 17 March were made using it.

I am asked would I recommend it. Well, yes, if you know what you are letting yourself in for.

Plus features are many - small size of the control unit, nifty touch screen controls, reasonable price, RF DSP, 4m for Europe, good frequency stability for data modes, USB lead to PC allowing direct audio in/out for data, DStar, coverage up to 70cms, ....

The snags I have experienced and my solutions are - low output powers on SSB (needs separate microphone with compressor), "clicking noise" (not a big thing, I am ignoring it), RF getting back into the control cable (use a short screened ethernet cable CAT6 or higher), deep cut on AGC a problem with QRN (electric fence problem in my case, turn AGC off).

OK, there are some problems, which are capable of being fixed. I complained to Icom about the clicking noise and they said they were looking into it and that they would reply with a solution soon. They did not reply. Also, the local dealer said the same thing and never replied. We are on our own with this one, but it is better just ignored.

For SSB and FM I use an Adonis 508 microphone set to low compression. That allows me to get the power up to the stated outputs, more or less. When I tried to raise this issue on the various sites, I got lectures about the difference between peak and mean power on SSB. Look, I know about that. Yes, I do have a peak reading power meter. There is just no way my 7100 can run the stated peak power on SSB using the internal compression and the supplied mic. But with an external amplified mic and the internal compression turned off I can get good results. And I DO  KNOW ABOUT THE DIFFERENCE BETWEEN PEAK AND AVERAGE POWER.

EDIT - there is a mod for this which I have not tried, but I know some people who have. There are in fact two mods here, however I believe that only one of them should be done (the soft one looks best to me) - see here http://gm4fvm.blogspot.co.uk/2016/02/ic-7100-low-ssb-output-surgical-solution.html

On data modes it is a triumph. It runs full stated power for ages and does not complain - like a meteor scatter contact with Italy lasting 3 hours! I have used it on FSK441, WSPR, JT65, JT9 PSK, JT6 ... all fine. No problem there at all, which makes the SSB performance a bit disappointing. But I fitted an external mic and I am in business on SSB too.

I don't use DStar so I cannot comment on that. Receiver wise it is OK, but I mostly use 12m and 10m on HF. I would guess it is OK on 80m and top band, but at this price it might not be brilliant in adverse conditions. I bought an LDG IT-100 ATU which is great but I have not used it much. My IC-7100 runs fine on 2m and 70cms.

It might be helping that my IC-7100 generally runs into linear amplifiers, which may cover up the low SSB power issue - on 6m an RM VLA150, on 4m a TE Systems 0610G and on 2m a Microset SR200. With that set-up - it blasts along.

So, I am happy enough and I would not want to put anyone off. But it should be better on SSB transmit. If the touch screen works first time it seems to be fine, in the shack anyway. Not sure how it would work portable or mobile where it would get strong light hitting it. The control unit stays steady if you extend the stabilising feet behind it.

OK, I am peeved to buy a whizzo rig with an internal DSP compressor, and then turn the internal system off and have to use a 1970s technology outboard mic. But after 18 months I have got over that one. It is OK. I wouldn't put anyone off. And for Europeans (or Africans or Asians in some places!) looking for a 4m/ 70MHz rig, it is a reasonable choice.

Finally, a recent firmware upgrade to the DSP and audio might have had the effect of helping the AGC dip issue. It seems better, but it has not gone away. I would suggest that you live somewhere away from electric fences.

Jim
GM4FVM

Wednesday, 18 March 2015

Aurora finale & propagation predictions?

Well, it is the day after St Patricks Day.

The GOES magnetometer graph of the event is shown, thanks to the Solarham page. The scale has had to be lengthened, as usually it does not extend much beyond the bottom of the daily sine-wave type variations. you can see that the magnetic fields were heavily disturbed.


The second phase of the 17 March event went on after midnight, but I finally ran out of reserves about 23:30. After that US and Canadian amateurs did good work all night. I did manage to work a couple more stations, G4ASR and G4RGK before pulling the big switch at 23:44. The beacons in GI were still coming in and I could hear traces of signals on the calling frequencies, but I was, basically, banjaxed.

At about16:00 the next day the HF bands are still battered after the shock. My favourite 10m has been fairly well closed all the past 24 hours. It will return eventually. There have been a few more auroral contacts in Europe this afternoon but I suspect this one is now over.

OK, I have to say that a successful aurora for me usually invovles five or six stations. Typically that is a couple of GMs and maybe an LA or an OZ. Sometimes something exotic like Faeroes Islands or Jan Mayen spice it all up a bit. So the St Patrick's Day event 2015, with 45 stations worked, is a big deal. Even then I am not entirely happy. If I had been able to use 6 metres I may have joined in a trans-Atlantic opening (though that seemed further South). The stations I did work were not very evenly distributed, with a lot of G stations, several EIs, OZs and PAs. That pattern was actually quite localised. There were no OHs, DKs or SPs heard here. I cannot complain though.

The question arises, can these events not be more accurately predicted? Frankly I would say "no". I know that there are all sorts of predictions published, but they never seem to me to be able to avoid giving many "false positives". In other words, they warn you of things which do not happen.

Other predictions (and I will not say whose, but they call themselves a National Radio Society) are so bland as to be useless. "It is not Summer yet so don't expect Sporadic E" (obvious, and occasionally wrong too), "There are no meteor showers predicted, so you could use random metor scatter instead" (duh!), and "the weather looks good so maybe there will be some tropo" (yeah, like you care about the weather where I am ). If those are predictions, I could do without them.

I do my own predictions. I watch Solarham (I will post a link to the site address alongside this post). Then I look at what is predicted there, interpret it my own way, and act accordingly. And I too get a lot of "false positives". But I was ready for this CME and aurora so I am happy enough.

Solarham do not predict radio events. They describe the solar situation, and you have to work out the radio effects yourself. Fair enough, I like to use my brain. This is a scientific hobby after all. But if the great US agencies like NASA and NOAA get caught on the hop by the St Patrick's Day event (they predicted a "possible glancing blow"), then my little string of seaweed can hardly predict the weather. I believe that nobody can predict the random events on a complex system like the Sun, and then accurately transfer the likely effects across space to Ayton, Berwickshire.

When is a "false positive" OK? When it is MY "false positive". That way I only have myself to blame.

73

Jim
GM4FVM

Tuesday, 17 March 2015

Aurora +++

Well, St Patrick's Day 2015 is not over here yet, and I am taking a few minutes out to reflect on "the day that was in it".

The aurora I speculated on did indeed arrive. Nothing visible as it was cloudy and misty, dreich as they say round here.

I am posting below the 10m WSPR waterfall during the height of the event. Note the spread out smudged traces and the snow effects. Others on lower bands reported very wide traces.

On VHF it started by me hearing the 2m Ballycastle beacon GB3NGI go auroral. It is only about 270km from me, and I can hear it T5 if I beam at it. But I was hearing it distorted, beaming at 50 degrees (East of North East) whereas it is West of me. Yes, 270km, but the signal is travelling via the auroral curtain somewhere over the Artic Circle.

As the 2m stations were pretty distorted, and right now I do not have a 6m antenna ($£%&***&), the only place to be was 4m. Business as usual there then. I started on 70.200, and worked OZ3ZW at at 14:20. We had to have two goes at it as he could not copy my callsign through the auroral distortion. After that I worked most of the time up until 17:50, moving down to 70.194 and even 70.180 at times to escape the pack of stations.

I worked 44 stations, though I had to take a break at about 17:00 as I had gone hoarse. They were from G, GM, GW, PA, ON, OZ, LA and EI. I worked 6 new squares, two in Denmark, two in Ireland and two in England. Signals were very strong. As is usually the case, the 4m signals were a lot less distorted than the 2m ones.

All the QSOs were nice of course, but a couple were really nice. Working Henning OZ1JXY is always a pleasure, and it took less than our usual 30 minutes meteor scatter contact. ON4ADI called me on CW and I had a lovely contact with him. I did not subject him to my ropey morse, but I enjoyed his careful, accurate and perfectly timed code. There were many old friends amongst the list, but I just had to plough on and keep working them. At one stage I had a pileup and I am sorry if I missed anyone. I know that Jaap PA0O heard me, and I think I heard him at one stage in the pileup, so sorry if I missed you. I only worked one GM - Andy GM4JR.

That was a classic VHF opening. You work your socks off and then it is over. Suddenly it is there, and just as suddenly it is gone. But it did not really end at 17:50, as the Kp index, which was 8, fell to about 6 and now at 22:30 it is back to 8 again. I can hear CW with AU tone on 70.200 but too low to copy.

At one stage this afternoon I tuned round and I could hear all of the UK beacons and EI4RF via Aurora, with the single exception of the Tring one. I also heard GM8RBR's personal beacon, a favourite of mine. Even now at 22:30 I can still hear auroral tones from GB3CFG in Carrickfergus on 4m and GB3NGI on the Antrim Plateau on 2m. So the aurora is over, as suddenly as it came, and welcome to the second aurora of the day.

Thanks everyone for a great night.

Jim
GM4FVM

CME shock wave and 10 metre condiitions

12:00z 170315

A Coronal Mass Ejection shock wave reached earth in the early hours of St Patricks Day (17 March 2015). Nothing too special about that but they have been rare of late.

On 10m my daily routine of WSPR work has shown strong signals from VK and Spoadic E arriving from Europe. A bit of a surprise was hearing PU3WSF before mid day.


There was probably an HF blackout about 04:00 when the shock hit, and now we have the results on 10m. It depends how the stream of particles arriving from the Sun are polarised as to whether we will have an aurora or better conditions. If the "Bz component" is positive, not much will happen. Right now Bz is -2.9 and the solar wind speed is over 600, both necessary conditions for an aurora. But for me at 56 degree North and 2 West it usually takes a larger Bz number at, say, 15:00 up to midnight, for this to work.

 However, we will see. The Sun has a habit of surprising us. Maybe the negative Bz will shoot up, maybe not. Maybe 2m will open with auroral signals, maybe 10m will have more sporadic E, maybe none of the above.

I picked a bad time to be off 6m if it does get good.

73
Jim

Monday, 16 March 2015

What is the point of FM on the 4 metre band?

It is now five years since I installed 4m FM at this location. Time for a review.

Of course I have been on and off 4m AM and FM for almost 40 years, but this relates to the period since I arrived here.

VHF FM is viewed as a local chat mode, so you would expect me to have worked a lot of locals. My Sirio J Pole antenna is mounted on a pair of T and K brackets, as shown.

The figures for fixed stations look like this over the five years:-

Total number of GM stations worked = 6
Total number of G stations worked = 2

Not a whole bunch for a five year period. Only 3 of these 8 are still active on the band.

If you widen the scope to include the number of stations which drive past down the busy A1 road, which links Edinburgh with London, the figures increase, but not much. I have worked one GM mobile one G mobile, and one in both jurisdictions. Then there area couple of people up hills and things, 4 GM portables, and 4 G portables.

The point is that I have been keeping a watch on this local FM band for five years for almost no result in terms of local stations. The only variety has been a few hill toppers and drivers happening to pass by. Don't believe all this stuff about local FM activity all over the UK.

But here are few other statistics, again for fixed stations ...

Total number stations worked -- Scotland = 6   Finland = 10
Total number of stations worked in England = 2 Total of countries worked = 13

So I have worked 66% more Finns on this local band than Scots. And I have worked 13 countries, but only 2 fixed stations in England. In fact, I have worked 22 stations outside the UK, compared to 2 in England. England is less than 5 miles away.

Lumping in all the non-fixed stations = 22 stations oustide the UK, compared to 20, all types, including /M and /P, anywhere in the UK. Even to get the 20 for the UK, I have added the mobile station I worked as he travelled between G and GM as being in both countries. So he counts as two stations!

I would offer this advice to anybody thinking of buying a 4m FM radio. Forget the locals and try to work some DX. It is there. If you are looking for 4m FM activity in most parts of the UK expect VERY low activity levels, but wait for the Summer and work some DX. It is tons more fun.

The DX potential makes it worth it for me.

There is no need for somebody to tell me that SSB would have netted a lot more DX. I know that, and I have worked 33 countries on that mode. But here we are talking about FM, a mode where ex-PMR rigs can be found for £30 or so and we all use simple antennas.


I bet the same story applies to 6m FM.

Jim
GM4FVM

Saturday, 14 March 2015

Aurora and Norwegian Magnetometers.

I am posting a link on the side bar to a stack of Norwegian magnetometers. When they go negative we know that auroral propagation is possible. The one I watch is Rorvik ("rvk"). Thanks to Gianfranco, now IU1DZZ, for giving me the link in the first place.

Here is a screenshot of today's magnetometers. There is a bit of disturbance - I wonder will we get aurora..


Worth keeping an eye on if you can access auroral propagation, and it gives warning of HF blackouts too.  These are the relevant ones for me; you can find the Boulder Colorado one and the Sundsvall one in Sweden on the SolarHam pages.

Jim

More meteor scatter

Another FSK441 QSO on 4 metres (70.230 MHz) today, this time with Henning OZ1JXY.

With WSJT modes you send a message for 30 seconds every minutes, and wait to see if you can hear a reply in the other 30 seconds. So you keep sending the same thing and hope you get the right reply. Sometimes you keep receiving the same message, which only confirms that the other station HAS NOT received your message.

This time it went as follows:-

At 12:26 I received OZ1JXY CQ OZ1JXY CQ
At 12:27 I started sending "JXY GM4FVM 26 26 26"
Rx 12:28 CQ OZ1JXY CQ
Rx 12:29 SQ OZ1JXY (SQ is the sort of distortion you get for CQ sometimes)
Rx 12:44  GM4FVM OZ7JXY R26 R26 GM4FVM OZ1JXY R26 R26
At 12:44 I started sending "RRRR RRRR GM4FVM (or RRRR RRRR FVM at times)"
Rx 12:46 R26 R26 GM4FVM OZ1JXY R26 R26
Rx 12:48 $M4FVM OZ1JXY P1
Rx 12:49 R6 R26  GM4FVM OZ1JXY R2 R26
Rx 12:52  73 FVM OZ1JXY 73 73
At 12:52 I started sending "73 73 73 GM4FVM"
Rx 12:55 73 FVM GZ1JXY
Rx 13:01 CQ OZ1JXY

So, I started sending my report at 12:27, but I knew that Henning had not heard it at 12:28 and 12:29. Then there was a gap when I heard nothing - maybe he had heard me, I would need to wait for the next copied message. That took another 15 minutes and then I knew that he had heard me and was also giving a 26 report. So I started sending RRRR to confirm receipt of the report at 12:44 and at 12:46 I knew that Henning still had not heard it. Also, at 12:49 he had not heard it, as he was still sending the report. But at 12:52 when I got the 73 I knew that he had heard my RRRR and the QSO was complete (though I usually send 73 too for a couple of cycles just to confirm). Then when I saw him calling CQ I know it is all over.

If you are used to other modes you will find this a bit baffling. It is just like JT65 on HF, you just keep sending your message, and you know when the other station has copied it as they change their message in sequence. It is the 15 minute period (sometimes MUCH longer) of sending reports, when I do not know if Henning has heard them, is what gets me excited. Has he either -
a) not heard ME, and it still calling CQ, or
b) has heard ME, is replying with his report, and I am not hearing HIM
That is the moment when meteor scatter comes alive for me. Have enough meteorites hit the atmoshpere, at the right place, at the right speed, at the right size?

Anyway, Henning and I keep this up over a 735km path - too short by most theories. I really appreciate his enthusiasm as it keeps me going in adverse conditions.



73
Jim

Friday, 13 March 2015

Nice Meteor Scatter contact into Poland


Thanks to Jerzy SP9HWY for this contact ....

Strong bursts over a path 1538km long!

This is interesting as it is on March 13 at around 15:00 GMT. Logic states that Meteor Scatter is better overnight and from mid April to early January.

Clearly my new 6 element for 70MHz is working as I had hoped. Frankly, I put it up hoping to work Jerzy more often. Previously he has been on the edge of my area of operation and only workable during shower peaks. So maybe something turns out right after all.

Other equipment was WSJT10 software, an Icom IC7100 running 9W of FSK441 into a TE Systems linear putting out 120W into the 6 element Yagi at 10m agl. Site is 60m asl.

That cheered me up, and now Katy the cat has jumped onto my knee to share in the joy.

Jim

Is my Yaesu FT-817 a "keeper"?

I bought my FT-817 from LAM electronics in Yorkshire three or four years ago. It competes with my Flex 1500 for my affections. They were both bought to drive 70MHz transverters, but now neither of them does that. Do I need both of them?

Here is the FT-817, sitting beside the ZLP electronics data interface and CAT control which drive it on 12m and 10m WSPR pretty well every day. It looks dusty but in fact that is just worn out paint and scratches on the covers.

So why do I like that 817 when its younger and more modern cousin the Flex sits nearby, turned off (the Flex tends to work during the Sporadic E season)? Well, although I use the Flex and the 817 for the same job, they could hardly be more different.

Lets us do some comparisons:-

Theoretically they both run 5W output. The Flex does, but the 817 soon loses puff as it warms up, falling to about 2.5 watts. Either I keep a fan on it, or I run it at 100mW anyway. Flex 1 vote == 817 0 votes

The 817 has a handy SWR meter which is very useful portable on holiday Flex 1 == 817 1

The 817 has an internal battery, but it does not work very well. No votes there.

The Flex is rather inaccurate in its frequency readout (60hz out on 10m, 100hz out on 6m). The 817's frequency readout is only to 10hz, as opposed to the Flex 1hz.  Though these errors are insignificant for most purposes, they matter for WSPR. What makes the 817 better (10hz on 10m) is the high-stability oscillator which I bought and fitted. So it is only stable if you spend more money. No votes there either.

The Flex has a wonderful set of adjustable filters which work brilliantly - the 817 only has a barn door SSB filter as standard. You can fit either a CW or a better SSB filter (which I did) but not both unless you use a bodge board which may or may not fit. Even then you can only have two filters, and at extra cost. Flex 2 == 817 1

The Flex has a glorious panadaptor readout whereas the 817 has a poor little screen with complex menus to work through (only because I used to have an FT-897 with a bigger screen can I understand the menus). Flex 3 == 817 1

The 817 works "stand-alone", whereas the Flex needs a computer Flex 3 == 817 2

The Flex creates sound and CAT ports in the computer, whereas the 817 needs costly and bulky data and CAT interfaces. Also, my 817 seems to pick up a lot of noise down the CAT lead which no amount of screening stops. Flex 4 == 817 2

I could go on but despite the fact that the 817 has 2m and 70cms, it really is a bit dowdy and old-fashioned compared to the Flex. So why is it still here?

I have glorious memories of taking the 817 to foreign parts. It is bashed and scratched from airport baggage searches. Sitting on the balcony of an apartment in Grrece I worked an Austrian station on 6metres using the internal batteries. I have taken it to Ireland, Belgium, France, Greece, Portugal, Spain, Madeira etc. I can use it abroad to listen to FM broadcast stations. I take it to our caravan on trips all round the UK.

It has one very handy feature for an HF QRP man like myself. It has an output attenuator in steps of 3dB, 6dB and 10dB. That lets me go down to 1mW and work 3000km on WSPR, which is equivalent to 3 million km per watt. Yes, the Flex can do that, but it is not so easy as clicking a switch. So I have the FT-817 set to 100mW for normal purposes, and I turn on an RM KL 203 PA for a switch to 1watt, or use the attenuator to cut the power to 50mW, 20mW or 10mW. Neat.

I have spent money on it - the high-stability oscillator, the SSB filter, the interfaces and the legs, amongst other things. It was not cheap to start with. To be really effective it needs lithium battery technology, DSP and a better readout, but then as an old design I guess it will just be replaced by Yaesu someday

So it sits here with no microphone connected, chuntering away at 100mW or less. It may be an old design and not have fancy DSP or software controls. But it does a job and it is an old friend.

I guess it will stay for a while yet.

Jim

Thursday, 12 March 2015

All change on the VHF antenna front ...

This is my new 6 element Yagi. Below it is my 10 element 2 metre beam, which now looks very small by comparison.



A few words of explanation. (few words? me? you are kidding!) On my Tenna mast I used to have a Vine 4/6m beam. That was 4 elements on 4metres, and 3 elements on 6meters. That was actually pretty good and it worked well because I have a restriction on the size of antenna I can have. It needs to be either maximum of 2 metres balanced across the mast, or shifted so that less than 1 metre extends on one side of the mast. So the Vine, which has a 2 metre long boom, was just fine. I could then lower it with the boom parallel to the ground. The 10ele worked too, as it is supported off centre and the short end is also less than 1 metre off to one side of the boom, so I could lower the mast IF the antennas were pointed just North of West.

I used to get annoyed about this as if I moved the mast I could use longer antennas, but is that really what I wanted to do? I really wanted a Tonna 9 element 2metre antenna, but with a boom just over 3metres it would not fit. However, I knew that I could do better than the 10 element, and in the end I bought a 6 element 2metre quad. That is a fine antenna, but I still felt restricted by the 2metre boom limit.

One day it finally dawned on me. The Vine was 2 metres by 3 metres (2m boom and 3m widest element.). But instead of 2x3 I could fit in 3x2. In other words, if I just had a 4metre beam instead of a 4/6metre dual band, it would only be 2m wide and could be 3m long in the boom (in fact any length of boom really). And a Tonna would then fit that way round!

This caused more head scratching. As the 4m beam I settled on, the Sandpiper one, has boom supports then the only thing I could fit under it was one other antenna. This would have to be the 2m one as the boom has to be pointing downwards when I lower it and thus a 6m would not fit (3m widest elements too long to fit). So for now I do not have a 6m antenna up. And the 2m quad no longer fits either.

Later I may put up a 6m vertical (I also have a 6m half wave vertical from Sandpiper).

So there you go. Lots of complicated stuff, but basically multiband 4/6m beam down, 2m quad down, 6ele 4m yagi up, 10ele 2m yagi up. Do I prefer this? Oh yes! Do I miss 6m --- yes.

OK, so the present antenna round down is
those two VHF yagis,
a 10/12m vertical dipole,
a 2m/70cms vertical and
a 4m vertical.

So far so good but I need to put something up for 6m. I have a Diamond 2 element (a sort of HB9CV) in the garage. that might go up soon.

If you are wondering why the 10element 2m went back up instead of the much wished for Tonna. Well, while I dithered Tonna stopped making them. Bah! Still, they may become available later. Maybe. Otherwise something better than the Diamond 10 element is due eventually.

Anybody want a used 4m/6m dual band yagi or a used 6 element 2m quad????

Jim